Cable (349)

This 8-m active extension can be used alone or as part of the Lindy USB 3.0 Active Extension System Pro. This is a modular solution that can combine multiple USB 3.0 active extension cables Pro and a USB 3.0 Active Extension Hub Pro to distribute USB sign

Cable cutter insulated with multi-component casings, VDE-tested 250 mm For cutting copper and aluminium cables, single and multi-wire. Not suitable for steel wire and wire cable. Hardened precision-ground blades. Cuts smoothly and cleanly without crush

Ergonomically designed handle shape with pleasantly designed slip guard More safety thanks to non-slip soft components Good power transmission when pulling the knife through thumb recess and ''finger hook'' at the end of the handle Transparent protecti

with crimping pliers 97 52 36 and self-adjusting insulation stripper 12 42 195 in a TANOS MINI-systainer® (solid plastic box) T-Loc fastener for one-handed operation: open or close the systainer® with one turn and connect to a second systainer® opening wh

Cable with a 9-pin D-Sub port and a 25-pin D-sub connector Connects PCs to modems Connector housing moulded for optimum strain relief, no cable breaks Excellent shielding prevents data loss and electromagnetic interference Manual locking screws Gold-

Cable for connecting a monitor to a graphics card or a VGA distributor 14 cables and an additional shielding cable connected to the cable's foil shielding and both connectors Moulded connector housing Manual locking screws

Combination/cable shears for copper and aluminium cable, with sharp, precision-ground blades, adjustable screwed joint. Length 140 mm Cutting force: Copper up to 10 mm in diameter Aluminium up to 24 mm in diameter

Small, light, strong: pleasant cutting without squeezing at only 160 mm size. Noticeably less effort required: The graduations cut wires one after the other, the cut is up to 40% lighter than standard cable cutters of the same length! Ergonomic leg design

Cable with a 9-pin D-Sub port and a 25-pin D-sub connector Connects PCs to modems Connector housing moulded for optimum strain relief, no cable breaks Excellent shielding prevents data loss and electromagnetic interference Manual locking screws Gold-

Cable jacket knife, VDE-tested up to 1000 V. Insulated blade backs, with protective cap and sliding shoe on blade tip, as a result, there is no damage to the inner conductor insulation. Length: 180 mm

For hard wire cables, also suitable for cabling and round steel • Precise, effortless screwed joint • With safety catch Special blade geometry prevents the wire cable fanning out Chrome vanadium high-performance steel, oil-hardened and tempered

Cable shears for copper and aluminium cable. Sharp, hardened precision-ground blades, polished, no crushing, no deformation, adjustable screwed joint. Length: 164 mm Cutting force: Copper up to 15 mm in diameter Aluminium up to 50 mm in diameter

Cable for connecting a hard disk via SATA 3.0 Gbps (SATA II), backwards compatible with SATA 1.5 Gbps (SATA I) 4-pin cable with ground leads Connections: two internal 7-pin SATA connectors Transfer rate up to 3.0 Gbps (SATA II)

tool burnished, handles with multi-component grips Style 2: internal opening spring, protected and captive

For connecting high-speed SATA hard disks in the PC housing. Cable for connecting hard disks using SATA technology Transfer rate of up to 6.0 Gbps (SATA II) 4-pin cable with ground leads Connections: Two internal 7-pin SATA connectors with snap-on clos

Impact-resistant plastic enclosure • Universal stripping tool for coaxial cables RG 59, RG 6, RG 7, RG 11 • For stripping outer sheathing and interior insulation in a single process • Adjustable stripping blade for round cabling • Two stripping blades for

Knipex crimping die For KN 97 43. For insulated cable shoes 0.5-10 mm².

Cable with two 25-pin D-Sub connectors Connects devices such as a switchbox to a computer 25 cables connected 1: 1 Shielding cable, connected to the cable's foil shielding and both connectors Connector housing moulded with special plastic for optimum

Single-handed crimping lever pliers from KNIPEX For non-insulated cable shoes from 0.5 to 10.0 mm². Length: 220 mm New crimping pliers with precision profiles and self-releasing lock offer amazingly high force strengthening despite compact dimensions and

tool burnished, handles with multi-component grips for cutting and shortening cable ducts, also for plastic material up to 4.0 mm thickness special lever transmission very effective blade geometry tool body: high-grade chrome vanadium electric steel, oil-

Cable with two 25-pin D-Sub connectors Connects devices such as a switchbox to a computer 25 cables connected 1: 1 Shielding cable, connected to the cable's foil shielding and both connectors Connector housing moulded with special plastic for optimum

Cable with two 9-pin D-Sub connectors Connects interfaces such as the serial IBM AT to a switch box All cables connected 1: 1 Shielding cable, connected to the cable's foil shielding and both connectors

Single-handed crimping lever pliers from KNIPEX For insulated cable shoes from 0.5 to 6.0 mm². Length: 220 mm New crimping pliers with precision profiles and self-releasing lock offer amazingly high force strengthening despite compact dimensions and with

for single, multiple and fine stranded conductors with plastic or rubber insulation max. 5.0 mm dia. or resp. 10 mm² cable cross section Increments in the jaw provide a visual orientation aid for stripping consistent lengths (11 mm and 16 mm) easy adjust

For cutting cables, stripping wires and crimping insulated and non-insulated cable shoes and plug connectors and open plug connectors • With threaded holes for cutting off copper or MS threaded pins with M 2.6/3.0/3.5/4.0 and 5.0 mm • Special steel, high

The USB-C extension cable EX-1408 extends your USB 3.2 Gen 2x1 line by 5 m. Up to three EX-1408 devices can be installed in series to achieve a maximum length of 15 m. In this case, an additional 5 V/1.5 A power supply will need to be installed. A connect

Miniature metal USB 3.2 Gen 1 hub with four ports. 20 cm USB-C cable. Input: USB 3.2 Gen 1 Output: USB 3.2 Gen 1, 4-port output PC connection: USB type C-M, fixed cable, 20 cm cable Power supply: via bus Design: Metal enclosure Miniature metal USB-C 3

Miniature metal hub USB 3.2 Gen 1 (USB 3.0) AXAGON HUE-M1A quickly and easily connects up to four USB devices to your laptop or computer. Input: USB 3.2 Gen 1 Output: USB 3.2 Gen 1, 4-port output PC connection: USB type A-M, fixed cable, 20 cm cable Po

For stripping all standard coaxial cables from 4.8 to 7.5 mm in diameter (such as for TV and satellite reception), also suitable for PVC-Flex 3 x 0.75 mm² With length scale from 5.0 to 20.0 mm Two-level, hinged stripping tool With opening spring and lo

Cable for connecting a hard disk via SATA 3.0 Gbps (SATA II), backwards compatible with SATA 1.5 Gbps (SATA I) 4-pin cable with ground leads Connections: two internal 7-pin SATA connectors Transfer rate up to 3.0 Gbps (SATA II)

Cable with two 9-pin D-Sub connectors Connects interfaces such as the serial IBM AT to a switch box All cables connected 1: 1 Shielding cable, connected to the cable's foil shielding and both connectors

Cable knife, VDE-tested 1000 V. Insulated blade backs, with protective cap. Length 180 mm

tool chrome plated, handles with dipped insulation, VDE-tested IEC 60900DIN EN 60900

First hand ratchet cable cutter for one and two-handed operation for cutting copper and aluminium cable up to a diameter of 60 mm. • Simple handling as a result of low weight (800 g) and compact design (320 mm in length) — can be used even in confined spa

Small, light, strong: pleasant cutting without squeezing at only 160 mm size. Noticeably less effort required: The graduations cut wires one after the other, the cut is up to 40% lighter than standard cable cutters of the same length! Ergonomic leg design

Knipex cable knife with ergonomically designed safety handle, interchangeable blade with special cut. With hinged blade guard, integrated in handle, captive. VDE-insulated according to DIN EN 60900 up to 1000 V. Length: 185 mm

In TANOS MINI-systainer® (robust plastic box) Two stackable plastic inserts with six trays each for connectors With an assortment of common cable connectors Included in delivery 97 90 21 (13) No. 97 52 36 KNIPEX PreciForce® 1 97 99 01 blade receptacles 25

Cable cutter for cutting flat ribbon cabling up to 56 mm in width without crushing. Replaceable cutting support and stop angle for right-angled cutting. Replaceable standard blades. Length 215 mm, nickel-plated.

For cutting copper and aluminium single conductors as well as multiple stranded cables. not suitable for steel wire and hard drawn copper conductors precision ground, hardened blade clean and smooth cut without crushing and deformation easy cutting wit

First hand ratchet cable cutter for one and two-handed operation for cutting copper and aluminium cable up to a diameter of 60 mm. • Simple handling as a result of low weight (800 g) and compact design (320 mm in length) — can be used even in confined spa