Cable (66)

KNIPEX cable shears with double blade Cuts smoothly and cleanly without crushing. For single and multi-strand copper and aluminium cable. Not suitable for steel wire and hard-drawn copper conductors. KNIPEX cable shears with double blade facilitates cutti

Knipex crimping die For KN 97 43. For insulated cable shoes 10-16 mm².

For stripping UTP and STP data cables 4.5 to 10.0 mm in diameter Stripping device for cross-sections of 0.2/0.3/0.8/1.5/2.5/4 mm² Two-level, hinged stripping tool With opening spring and locking pawl Mounting clip for secure storage Housing: Plastic,

tool burnished, handles with multi-component grips for cutting and shortening cable ducts, also for plastic material up to 4.0 mm thickness special lever transmission very effective blade geometry tool body: high-grade chrome vanadium electric steel, oil-

The NA-SEC2 is a fan accessory set consisting of three fully sleeved NA-EC2 30cm Extension Cables for 3-pin fans. The NA-EC2 cables provide ample reach for installing fans in larger enclosures and can be daisy-chained when more than 30cm are required. Sco

tool burnished, handles with multi-component grips

The NA-SYC1 chromax.black set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time.

tool burnished, handles with multi-component grips

for cutting copper and aluminium single conductors as well as multiple stranded cables not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades clean and smooth cut without crushing and deformation easy cutting wi

For Bowden cables and soft wire ropes (including V2A) up to diameter of 3.0 mm Light, clean cut thanks to special cutting edge shape Sickle-shaped cutting edges enclose the cut material and prevent splicing of the wire rope Little force needed owing to

With replaceable blade

• For cutting copper and aluminium cables, single and multi-wire • Not suitable for steel wire and hard-drawn copper conductors • Hardened precision-ground blades • Cuts smoothly and cleanly without crushing • Easy cutting with one-handed use • Clamping p

Shielded PROFINET drag chain cable, M12 to RJ45 Ethernet connection cable with straight plugs. Pre-assembled IE wires M12, D-code, IP67, pin RJ45, IP20 Operating temperature: -40 to 70°C Length: 5 m

Cable cutters with ratchet principle For copper and aluminium cable, one-handed operation, two-stage sprocket drive for easy cutting. Cuts smoothly and cleanly without crushing, also suitable for stripping. Can be used even in confined spaces. Not suitabl

The NA-SYC1 is a fan accessory set consisting of two fully sleeved NA-YC1 Y-Cables for 4-pin PWM fans. The NA-YC1 Y-Cables make it possible to run two 4-pin PWM fans on a single fan header and to let the mainboard control the speed of both fans simultaneo

head polished, handles insulated, extrusion plastic-coated, VDE-tested IEC 60900DIN EN 60900

Cable cutter insulated with multi-component casings, VDE-tested 250 mm For cutting copper and aluminium cables, single and multi-wire. Not suitable for steel wire and wire cable. Hardened precision-ground blades. Cuts smoothly and cleanly without crush

Ergonomically designed handle shape with pleasantly designed slip guard More safety thanks to non-slip soft components Good power transmission when pulling the knife through thumb recess and ''finger hook'' at the end of the handle Transparent protecti

with crimping pliers 97 52 36 and self-adjusting insulation stripper 12 42 195 in a TANOS MINI-systainer® (solid plastic box) T-Loc fastener for one-handed operation: open or close the systainer® with one turn and connect to a second systainer® opening wh

Cable shears for copper and aluminium cable. Sharp, hardened precision-ground blades, polished, no crushing, no deformation, adjustable screwed joint. Length: 164 mm Cutting force: Copper up to 15 mm in diameter Aluminium up to 50 mm in diameter

Ergonomically designed handle shape with pleasantly designed slip guard More safety due to non-slip soft components Good power transmission when pulling the knife through thumb cavity and ''finger hook'' at the end of the handle Transparent protective cap

Extension cable, 5 m Height: 8.2 mm Width: 8.2 mm Length: 5000 mm Material: rubber

shiverpeaks®-BASIC-S-patch cable, cat.7 raw cable, RJ45 plugs cat.6, PIMF, NON-HALOGEN, purple, 5,0m

Combination/cable shears for copper and aluminium cable, with sharp, precision-ground blades, adjustable screwed joint. Length 140 mm Cutting force: Copper up to 10 mm in diameter Aluminium up to 24 mm in diameter

For stripping all standard coaxial cables from 4.8 to 7.5 mm in diameter (such as for TV and satellite reception), also suitable for PVC-Flex 3 x 0.75 mm² With length scale from 5.0 to 20.0 mm Two-level, hinged stripping tool With opening spring and lo

with crimping pliers 97 22 240 in a TANOS MINI-systainer® (solid plastic box) T-Loc fastener for one-handed operation: open or close the systainer® with one turn and connect to a second systainer® opening when connected: fast and simple access to content

Small, light, strong: pleasant cutting without squeezing at only 160 mm size. Noticeably less effort required: The graduations cut wires one after the other, the cut is up to 40% lighter than standard cable cutters of the same length! Ergonomic leg design

Cable jacket knife, VDE-tested up to 1000 V. Insulated blade backs, with protective cap and sliding shoe on blade tip, as a result, there is no damage to the inner conductor insulation. Length: 180 mm

For hard wire cables, also suitable for cabling and round steel • Precise, effortless screwed joint • With safety catch Special blade geometry prevents the wire cable fanning out Chrome vanadium high-performance steel, oil-hardened and tempered

Cable shears for copper and aluminium cable. Sharp, hardened precision-ground blades, polished, no crushing, no deformation, adjustable screwed joint. Length: 164 mm Cutting force: Copper up to 15 mm in diameter Aluminium up to 50 mm in diameter

The NA-SEC1 is a fan accessory set consisting of three fully sleeved NA-EC1 30cm Extension Cables for 4-pin PWM fans. The NA-EC1 cables provide ample reach for installing fans in larger enclosures and can be daisy-chained when more than 30cm are required.

tool burnished, handles with multi-component grips Style 2: internal opening spring, protected and captive

Impact-resistant plastic enclosure • Universal stripping tool for coaxial cables RG 59, RG 6, RG 7, RG 11 • For stripping outer sheathing and interior insulation in a single process • Adjustable stripping blade for round cabling • Two stripping blades for

Knipex crimping die For KN 97 43. For insulated cable shoes 0.5-10 mm².

Single-handed crimping lever pliers from KNIPEX For non-insulated cable shoes from 0.5 to 10.0 mm². Length: 220 mm New crimping pliers with precision profiles and self-releasing lock offer amazingly high force strengthening despite compact dimensions and

Single-handed crimping lever pliers from KNIPEX For insulated cable shoes from 0.5 to 6.0 mm². Length: 220 mm New crimping pliers with precision profiles and self-releasing lock offer amazingly high force strengthening despite compact dimensions and with

for single, multiple and fine stranded conductors with plastic or rubber insulation max. 5.0 mm dia. or resp. 10 mm² cable cross section Increments in the jaw provide a visual orientation aid for stripping consistent lengths (11 mm and 16 mm) easy adjust

For cutting cables, stripping wires and crimping insulated and non-insulated cable shoes and plug connectors and open plug connectors • With threaded holes for cutting off copper or MS threaded pins with M 2.6/3.0/3.5/4.0 and 5.0 mm • Special steel, high

In TANOS MINI-systainer® (robust plastic box) Two stackable plastic inserts with six trays each for connectors With an assortment of common cable connectors Included in delivery 97 90 21 (13) No. 97 52 36 KNIPEX PreciForce® 1 97 99 01 blade receptacles 25

Cable cutter for cutting flat ribbon cabling up to 56 mm in width without crushing. Replaceable cutting support and stop angle for right-angled cutting. Replaceable standard blades. Length 215 mm, nickel-plated.