Cable (42)

The NA-SYC1 chromax.blue set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time.

The NA-SYC1 chromax.yellow set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time

• Rated voltage: 1000 V CAT III • Rated current: 2 A to 3 6A (with 2,5 mm², fully unrolled) • Cable: 0.75 mm² • Plug: Ø 4 mm • Length: 30 m • Color: red

4-pin PWM Y-cable for connecting 2 PWM fans to 1 PWM header on the motherboard

cable ties with 200 mm length and 2.5 mm width in transparent white made of UV- and weatherproof nylon. Cable management made easy - the cable organisers keep things tidy and help to avoid cable chaos. All details at a glance: For a secure hold during DIY

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

4-pin PWM Y cable for connecting 3 PWM fans to 1 PWM header on the motherboard

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

• Rated voltage: 250 V CAT II • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: yellow

shiverpeaks® BASIC-S cable pull-in aid, nylon, 4 mm, 60 m Use the cable pull-in aid to easily pull your cable through a conduit. There is an eyelet on the GRP pull wire. The enclosed wire loop allows you to attach the cable to the eyelet. The screw-on hea

shiverpeaks®-BASIC-S--Cable routing aid, nylon, 3 mm, 15 m Use the cable routing aid to pull your cabling through ductwork effortlessly. The nylon pull wire features an eyelet that the cable can be attached to, and a guide spring to make it easier to neg

EPA suitable. For working in electrostatically protected areas (ESD workplace/ESD protection zone). For connecting the table and floor coverings and for connection to a ground potential. cable with 1 megohm safety resistor with 2 push buttons 10/10 mm p

• Rated voltage: 1000 V CAT III • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 0.75 mm² • Plug: Ø 4 mm • Length: 30 m • Color: blue

The NA-SEC1 chromax.black set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, mult

EBP-Earth Bonding Point, EPA suitable. For working in electrostatically protected areas (ESD workplace/ESD protection zone). Earthing point for mounting underneath the table top. EBP / Earth Bonding Point = A common connection point to which ESD control e

Polyamide cable ties, black, UV-resistant. Tensile strength: approx. 80 N at 2.5 mm, 130 - 180 N at 3.5 mm, 220 N at 4.5 mm. Length: 280 mm Width: 3.5 mm Pack of 100 pieces Note: these cable ties are always packed slightly moist to extend the shelf life.

Very stable Quick to install Provides plenty of room for all cables Colour: silver Delivery: 2x cable ducts 530 x 110 x 80 mm Two cable ducts for clean cable routing under the desk

Earthing measurement cable, 4 mm connection, yellow, 50 m length, with cable reel

ESD discharge cable with integrated resistor. Spiral cable, 2x press-stud 10 mm/10 mm Length: 2.4 m

• Rated voltage: 250 V CAT II • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: blue

Connecting cable, red/black, angled/straight 4 mm connection, for HIOKI multimeters from product series DT425x/DT428x or similar, CAT III 1000 V, CAT IV 600 V, 120 cm length

ESD discharge cable with integrated resistor. Spiral cable, 3 mm press-stud to 10 mm press-stud Length: 2.4 m

cable ties with 300 mm length and 3.5 mm width in transparent white made of UV- and weatherproof nylon. Cable management made easy - the cable organisers keep things tidy and help to avoid cable chaos. All details at a glance: For a secure hold during DIY

EPA suitable. For working in electrostatic protected areas (ESD workplace/ESD protection zone). For connecting the table and floor coverings and for connection to an earth potential. with 1 megohm safety resistor 2 push buttons 10 mm for mats or floor co

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

• Rated voltage: 1000 V CAT III • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: blue

The NA-SEC1 chromax.red set is a fan accessory kit that includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, multiple NA

• Rated voltage: 250 V CAT II • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: red

The NA-SEC1 chromax.blue set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, multi

This Delock cable support is ideally suited to wall mounting for hanging laboratory cables or test equipment, enabling clear and tidy organisation. Specifications Cable support for wall mounting 2 x mounting holes Mounting hole diameter: approx. 8 mm 1

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

The NA-SYC1 chromax.green set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time.

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

This Delock cable support is ideally suited to wall mounting for hanging laboratory cables or test equipment, enabling clear and tidy organisation. Specifications Cable support for wall mounting 2 x mounting holes Mounting hole diameter: approx. 8 mm 1

The NA-SEC1 chromax.green set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, mult

The ÖLFLEX® CLASSIC 110 is a VDE-registered oil-resistant PVC control cable that can be flexibly used for a variety of applications. Flame-retardant in accordance with IEC 60332-1-2 Excellent chemical resistance Oil-resistant in accordance with DIN EN 5

shiverpeaks®-BASIC-S--Cable routing aid, nylon, 3 mm, 20 m Use the cable routing aid to pull your cabling through ductwork effortlessly. The nylon pull wire features an eyelet that the cable can be attached to, and a guide spring to make it easier to neg

Earthing measurement cable, 4 mm connection, red, 50 m length, with cable reel

The NA-SEC1 chromax.yellow set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, mul

cable ties 100 mm long and 2.5 mm wide in transparent white with text field (25 x 8 mm) made of UV and weatherproof nylon. Cable management made easy - the cable organisers keep things tidy and help to avoid cable chaos. The integrated, transverse labell