Cable (41)

The NA-SYC1 chromax.blue set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time.

The NA-SYC1 chromax.yellow set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time

• Rated voltage: 1000 V CAT III • Rated current: 2 A to 3 6A (with 2,5 mm², fully unrolled) • Cable: 0.75 mm² • Plug: Ø 4 mm • Length: 30 m • Color: red

The tesa Powerstrips® cable clip for easy fixing of cables in the home, home office and around the workplace. Product features • Brings order to the clutter of cables • Fixes cable up to a diameter of 8 mm* • Easy to mount without screws, dowels or nails

4-pin PWM Y-cable for connecting 2 PWM fans to 1 PWM header on the motherboard

For fine labelling on cables Specially designed for ultra-fine writing, marking and labelling on various types of cables. Cable marker with bullet nib, permanent, waterproof ink. Product characteristics Available in four colours as wallet only Use: Ready

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

4-pin PWM Y cable for connecting 3 PWM fans to 1 PWM header on the motherboard

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

• Rated voltage: 250 V CAT II • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: yellow

shiverpeaks® BASIC-S cable pull-in aid, nylon, 4 mm, 60 m Use the cable pull-in aid to easily pull your cable through a conduit. There is an eyelet on the GRP pull wire. The enclosed wire loop allows you to attach the cable to the eyelet. The screw-on hea

The connectors have been developed for use in systems-, control- and electrical equipment engineering. It is the responsibility of the user to check whether the connectors can also be used in other areas of application. To protect against unintentional op

shiverpeaks®-BASIC-S--Cable routing aid, nylon, 3 mm, 15 m Use the cable routing aid to pull your cabling through ductwork effortlessly. The nylon pull wire features an eyelet that the cable can be attached to, and a guide spring to make it easier to neg

EPA suitable. For working in electrostatically protected areas (ESD workplace/ESD protection zone). For connecting the table and floor coverings and for connection to a ground potential. cable with 1 megohm safety resistor with 2 push buttons 10/10 mm p

• Rated voltage: 1000 V CAT III • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 0.75 mm² • Plug: Ø 4 mm • Length: 30 m • Color: blue

The NA-SEC1 chromax.black set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, mult

EBP-Earth Bonding Point, EPA suitable. For working in electrostatically protected areas (ESD workplace/ESD protection zone). Earthing point for mounting underneath the table top. EBP / Earth Bonding Point = A common connection point to which ESD control e

Earthing measurement cable, 4 mm connection, yellow, 50 m length, with cable reel

ESD discharge cable with integrated resistor. Spiral cable, 2x press-stud 10 mm/10 mm Length: 2.4 m

• Rated voltage: 250 V CAT II • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: blue

Connecting cable, red/black, angled/straight 4 mm connection, for HIOKI multimeters from product series DT425x/DT428x or similar, CAT III 1000 V, CAT IV 600 V, 120 cm length

ESD discharge cable with integrated resistor. Spiral cable, 3 mm press-stud to 10 mm press-stud Length: 2.4 m

EPA suitable. For working in electrostatic protected areas (ESD workplace/ESD protection zone). For connecting the table and floor coverings and for connection to an earth potential. with 1 megohm safety resistor 2 push buttons 10 mm for mats or floor co

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

• Rated voltage: 1000 V CAT III • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: blue

The NA-SEC1 chromax.red set is a fan accessory kit that includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, multiple NA

The tone generator is used to apply a tone signal to a pair of wires or a single conductor and track it with the Inductive Receiver (Model R180001). The tone generator allows technicians to identify a wire in the middle of a bundle at a switching distribu

• Rated voltage: 250 V CAT II • Rated current: 2 A to 36 A (with 2,5 mm², fully unrolled) • Cable: 1,5 mm² • Plug: Ø 4 mm • Length: 50 m • Color: red

The NA-SEC1 chromax.blue set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, multi

This Delock cable support is ideally suited to wall mounting for hanging laboratory cables or test equipment, enabling clear and tidy organisation. Specifications Cable support for wall mounting 2 x mounting holes Mounting hole diameter: approx. 8 mm 1

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

The NA-SYC1 chromax.green set is a fan accessory kit consisting of three NA-YC1 Y cables. The NA-YC1 cables allow two 4-pin PWM fans to be operated on a single fan connection and the speed of both fans to be controlled by the motherboard at the same time.

This 4 pin fan cable by Delock with PWM support enables the extension of the fan connection. The 4 pin male fan connector is also suitable for the connection of a 3 pin fan connector without PWM support. Specification Connectors: 1 x 4 pin fan connector m

This Delock cable support is ideally suited to wall mounting for hanging laboratory cables or test equipment, enabling clear and tidy organisation. Specifications Cable support for wall mounting 2 x mounting holes Mounting hole diameter: approx. 8 mm 1

The NA-SEC1 chromax.green set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, mult

The ÖLFLEX® CLASSIC 110 is a VDE-registered oil-resistant PVC control cable that can be flexibly used for a variety of applications. Flame-retardant in accordance with IEC 60332-1-2 Excellent chemical resistance Oil-resistant in accordance with DIN EN 5

shiverpeaks®-BASIC-S--Cable routing aid, nylon, 3 mm, 20 m Use the cable routing aid to pull your cabling through ductwork effortlessly. The nylon pull wire features an eyelet that the cable can be attached to, and a guide spring to make it easier to neg

Earthing measurement cable, 4 mm connection, red, 50 m length, with cable reel

The NA-SEC1 chromax.yellow set is an accessory kit for fans and includes three NA-EC1 30-cm extension cables. The 4-pin connectors of the NA-EC1 cables are compatible with both 4-pin PWM and 3-pin fans. If larger cases require more than a 30-cm range, mul

shiverpeaks®-BASIC-S--Cable entry aid, nylon, 3 mm, 30m Use the cable entry aid to pull your cabling through ductwork effortlessly. An eyelet is provided on the nylon pull wire to fasten the cable to, and a guide spring to make it easier to negotiate ang